Maine Journeyman Plumbing Practice Exam

These questions are part of the practice quiz. Start practicing

• What is the primary function of a sump pump in a basement?
• How often should plumbing systems be inspected for leaks?
• What is the function of a Reduced Pressure Zone Valve (RPZ)?
• Which of the following best describes a pressure-reducing valve?
• What is the minimum size of a building drain for a residential plumbing system?
• What is the maximum allowable angle for a cleanout in a plumbing system?
• What type of lavatory is specified for residential use?
• What is the PSI requirement to lift water one foot vertically?
• Which plumbing term refers specifically to the lowest horizontal portion of a drainage system?
• What is the purpose of a cleanout in plumbing?
• What material is commonly used for drainage systems due to its corrosion resistance?
• What is the main purpose of the Uniform Plumbing Code?
• What is a significant factor in determining the layout of plumbing systems in a building?
• How is gray water categorized in plumbing?
• What is the maximum distance a water closet can be from a vent?
• What is the formula for calculating the total fixture units of a plumbing system?
• How are sump pumps powered in residential settings?
• What is the function of a sump pit in a plumbing system?
• If a hose bib is not properly winterized, what can occur?
• What type of valve is used for shut-off purposes in a plumbing system?
• What is a common material used for sewer pipes?
• What is a common consequence of not having a pressure-reducing valve in a high-pressure system?
• What is the drain size required for a kitchen sink?
• What is the purpose of a backflow prevention device?
• What should be installed to minimize thermal expansion in hot water systems?
• What type of system usually requires an Atmospheric Relief Valve?
• What is a cistern used for in plumbing?
• What is the required distance between a well and a septic tank?
• What is the purpose of a water softener?
• What is the maximum recommended distance between manholes in a sewer system?
• What is the term used to describe the slope of drainage pipes to facilitate flow?
• What is the nature of a Combined Sewer System?
• What is the primary function of a branch vent?
• What does a pressure switch control in a well system?
• How can you test for leaks in a plumbing system?
• What is the purpose of an Individual Vent in a plumbing system?
• When should a pressure-reducing valve be installed?
• Which of the following statements is true about drilled wells?
• What indicates that a drain line is blocked?
• How many fixture units does a standard kitchen sink typically represent?
• Which plumbing component is used for connecting different pipe types or sizes?
• What is the standard size for a double bowl kitchen sink?
• Which component is critical in ensuring water pressures remain at safe levels?
• What does the term 'fixture unit' refer to in plumbing?
• What defines the maximum depth for a driven well?
• What does the term "backflow" refer to in plumbing?
• What does the term "head pressure" refer to in plumbing?
• What is the required minimum distance of a septic tank from a building?
• Which type of valve is most commonly used to regulate water flow in plumbing?
• What is a common cause of slow drains in plumbing systems?
• What does the abbreviation BV stand for in plumbing terminology?
• What does "fixture unit" measure in plumbing?
• What is the standard drain size for urinals?
• What is a common sign of a clogged sewer line?
• What is the minimum height for a kitchen sink faucet above the flood rim?
• What is the primary function of a vent stack?
• How is rainwater classified in terms of mineral content?
• What is the standard width range for residential sink bases during cabinet installation?
• Which material is commonly used for potable water supply lines?
• Which type of toilet is best suited for residential applications?
• What is the purpose of a trap primer?
• What is an approved method of repairing a leak in a PEX pipe?
• What is the maximum slope allowed for a drain line in a residential plumbing system?
• Which type of valve is most commonly used to control water flow?
• In what circumstance is a double check valve assembly required?
• What is the ideal pressure range for residential water systems?
• What is the purpose of a loop vent in plumbing?
• What is a common type of device used in a commercial ice machine?
• What is the function of the main isolation valve in a plumbing system?
• What plumbing code section contains rules about water supply systems?
• What can excessive water pressure lead to in a plumbing system?
• What can happen when a plumbing system is not properly vented?
• What is the required drain size for a shower?
• Which fixture is required to be equipped with a backflow prevention device?
• What is the purpose of a water distribution system within a building?
• What is the general function of a pressure gauge in plumbing?
• What is an effective way to prevent corrosion in metal pipes?
• Which fitting is used to connect two pipes of different diameters?
• What type of fitting is used to change the direction of a plumbing pipe?
• What is the minimum required depth for a P-trap seal?
• Which component is essential for preventing backflow in plumbing?
• What do drain fields for effluent typically consist of?
• What defines a wet vent in plumbing systems?
• What distance between two plumbing systems ensures regulatory compliance?
• What does DWV stand for in plumbing terminology?
• Which plumbing fixtures usually require a separate vent?
• What does HB represent in plumbing terminology?
• What is the minimum diameter required for a residential drain line?
• What is the effect of having too much water pressure in a plumbing system?
• What is the primary function of a manhole in a sewer system?
• What is the proper drain size for a lavatory?
• What is the recommended pipe pitch for a drain field?
• What is the distance between water supply lines and drain lines in a wall?
• How far below the frost line should water lines typically be buried?
• What is the main purpose of a vacuum breaker in a plumbing system?
• What is the primary function of a heat exchanger in plumbing?
• What is the recommended depth for a dug well?
• What is the required distance for a vent pipe from a fixture?
• What does the term "cross-connection" mean in plumbing?
• How frequently should septic tanks be pumped?
• What does the term "drainage" refer to in plumbing?
• What does the abbreviation BS stand for in plumbing terminology?
• What does the term 'flood level rim' refer to in plumbing?
• What size is required for a lavatory drain?
• How deep can a drilled well typically be?
• Which type of pipe is commonly used for residential water supply lines?
• What is the minimum required slope for a drain pipe?
• Which plumbing fitting is used to change the direction of pipe flow?
• What is the maximum temperature for a residential hot water system?
• What is an acceptable use for cross-connection control in plumbing?
• What is the minimum size of a main sewer line for a residential building?
• What is the maximum distance allowed for a trap arm before it has to vent?
• What does UPC stand for in plumbing codes?
• What is necessary for a plumbing system to function correctly?
• What is the common size for a building drain's cleanout?
• What is the required inch spread for a 3-hole lavatory faucet setup?
• What is the primary purpose of a vent pipe in a plumbing system?
• What is the primary benefit of using a ball valve in plumbing?
• Which of the following is a function of a sump pump?
• Which plumbing code governs plumbing in Maine?
• Which of the following is crucial for preventing sewage odors in a plumbing system?
• What is the recommended pipe material for underground water supply lines?
• What is the required width for kitchen sink double bowl sizes?
• What is the minimum required slope for a drainage pipe?
• What is the purpose of an expansion tank in a plumbing system?
• What does SV stand for in plumbing systems?
• What device helps to prevent backflow in plumbing systems?
• Which of the following is the correct drain size for a non-handicap shower?
• What is the maximum temperature for water discharge from a water heater?
• What type of fitting is commonly used to change the direction of pipe flow by 90 degrees?
• What is the function of a backwater valve in plumbing?
• What is the minimum diameter for a soil stack vent in a commercial building?
• How must drain lines be installed with respect to other utilities?
• What does a dual check valve primarily protect against?
• What is a common issue that can occur from improper venting in a plumbing system?
• What is a characteristic feature of the venturi in a pump system?
• What does a trap primer do in plumbing systems?
• What is the purpose of a Vent Stack in a DWV system?
• What is the primary purpose of a backflow preventer?
• How often should sump pumps be tested for proper operation?
• Which type of lavatory is commonly used in commercial settings?
• How often should you inspect and clean your plumbing fixtures to prevent build-up?
• What does a plumbing inspector primarily check for during an inspection?
• What is the recommended height for a kitchen sink rim from the floor?
• What is the maximum water heater temperature setting recommended for residential use?
• What is the purpose of an air admittance valve?
• What is the maximum number of fixtures allowed on a 2-inch horizontal drain?
• In what type of soil conditions are driven wells most effectively used?
• Water service to a building primarily involves what?
• What is the main function of a Fixture Branch in plumbing?
• What is the typical pump depth range for a shallow well?
• What type of fitting is commonly used to change the direction of a pipe?
• What is the purpose of a P-Trap in plumbing?
• Which valve is specifically designed to handle low-pressure conditions in a well system?
• What is the purpose of a relief vent in plumbing?
• Which part of the plumbing system extends and goes through the roof?
• What is the required size of a vent pipe for a vertical stack serving 10 fixtures?
• What signifies that a water pipe may be frozen?
• What is the standard toilet clearance requirement from center to center?
• How does water pressure typically change with depth in a well?
• Which code governs plumbing installations in Maine?
• What is the minimum size of a trap for a kitchen sink?
• What is the drain size for a combination tub and shower?
• What is the primary function of a trap in plumbing systems?
• What is the required vent size for a 4-inch toilet drain?
• What is the diameter of the vent pipe required for a 3-inch drain?
• What is the purpose of a P-trap in plumbing?
• What is the primary purpose of plumbing venting?
• What is the purpose of a trap in a plumbing system?
• What type of piping is typically used for sewer lines?
• What is the minimum size requirement for shower space?
• What is the minimum clearance required above the flood rim in a sink for an air gap?
• Which component of a plumbing system is described as the vertical part that receives drainage from horizontal branches?
• What does BD refer to in residential plumbing?
• What is the typical water connection size for urinals?
• What must be done to ensure a proper installation of a gas water heater?
• What material can be used for venting systems?
• In a DWV system, what is primarily transported by the Waste Stack?
• What is the minimum size requirement for a non-handicap shower?
• What tool is typically used to unclog a drain line?
• What is the standard size for a bathtub?
• In plumbing, what does the term "static pressure" refer to?
• What are the two primary flushing mechanisms used in toilets?
• What specific design does a circuit vent serve?
• Which vent serves a battery venting design and connects to a vertical stack?
• What term is used to define the layer of saturated ground?
• What is the clearance required between discharge piping and a water supply line?
• What is the preferred angle for a shower drain to ensure proper water flow?
• What is the effect of having too many bends in a drainage system?
• What is the standard size for a single bowl kitchen sink?
• What type of material is often used for vent pipes in residential plumbing?
• What is the primary function of a drilled well?
• What does effluent refer to in the context of plumbing?
• What should be done before cutting into a plumbing pipe?
• Which size is commonly required for kitchen sink single bowls?
• How many inches must a toilet be from the wall to be considered compliant?
• In plumbing terminology, what does "DWV" signify?
• What is the primary reason for installing a vent system in plumbing?
• In a plumbing system, what does a vent pipe primarily prevent?
• What type of toilet is designed primarily for commercial use?
• What is the role of a plumbing trap?
• What is the purpose of a pressure relief valve on a water heater?
• What is the standard drain size for a tub?
• Which type of pipe is commonly used for potable water supply in Maine?
• What is a driven well primarily constructed with?
• What is the function of piping within a building called?
• What is the primary role of the portion of piping outside a building?
• What does "thermal expansion" refer to in plumbing systems?
• What is an acceptable method for connecting a vent pipe to a drainage pipe?
• Which valve type is often used for controlling the flow of water in a plumbing system?
• Which type of pipe material is often used for residential water supply lines?
• What is the standard distance requirement from the center of a toilet to the back wall?
• Which measurement indicates the pressure in a plumbing system?
• What type of vent is identified by the abbreviation RV?
• What does undisturbed soil between plumbing systems help to ensure?
• How can plumbing systems avoid potential damage from high water pressure?
• What is the maximum length of a horizontal run permitted for a 2-inch vent?
• Which component connects a Fixture Branch to the Waste Stack or Building Drain?
• How are plumbing pipes typically graded for drainage?
• How should PVC pipes be joined?
• What is termed a Fixture Drain in plumbing?
• What average water pressure is measured at sea level?
• Which plumbing component is designed to reduce pressure in the system?
• What is the purpose of a distribution box in a plumbing system?
• Which of the following pipe materials is least likely to corrode?
• What is the required distance of undisturbed soil between two trenches for plumbing systems?
• Which plumbing term indicates a component that serves more than one fixture drain?
• What is the minimum toilet clearance requirement from the center to the wall?
• In a residential plumbing system, what is the primary purpose of a cleanout?
• What does the term "potable water" mean?
• Upon noticing a water leak, what is the proper first step to take?
• What is a typical method for unblocking a drain?
• What materials are allowable for a building sewer pipe?
• What is the purpose of a hose bib vacuum breaker?